![windows serial terminal with auto baud windows serial terminal with auto baud](https://1.bp.blogspot.com/-f9umqTRoYjc/XiHIHM3pRJI/AAAAAAAAxIU/MewAPwwcrlM-X6pxTrmTnMGZrwCGGI5IQCLcBGAsYHQ/w1200-h630-p-k-no-nu/Terminal.png)
- Windows serial terminal with auto baud how to#
- Windows serial terminal with auto baud mac os x#
- Windows serial terminal with auto baud install#
- Windows serial terminal with auto baud driver#
The grounding lug location is on the back panel of the device.Įnsure that the grounding lug wire does not cover the fan opening.įigure 17.
Windows serial terminal with auto baud how to#
This section describes how to ground the device. Mounting the Router on the Wallīefore mounting the device, ensure that all unused holes at the sides of the device are protected with screws.īefore you begin this task, ensure that you have read and understood the safety warnings in the Preventing ESD Damage section of the Safety Warnings handout topic.īefore you connect the power or turn on the power to the device, you must provide an adequate device ground (earth) connection Position the device vertically on the wall. Secure the cable guides with four M6x12mm screws that are supplied with the cable kit. Position the cable guide against the front of the device, and align the four screw holes as shown in the figure.
Windows serial terminal with auto baud install#
Install cable guides before mounting the device on the wall. You can install the brackets as shown in the figure. Remove the wall mounting brackets from the accessory kit and position them beside the device.
![windows serial terminal with auto baud windows serial terminal with auto baud](https://downloads.guru/i/win10/Advanced-Serial-Port-Monitor_about_window_24708_650x200.jpg)
The device is shipped with wall mounting brackets that are to be secured on the sides of the device. Install the wall mounting brackets and cable guides on to the chassis before you mount the chassis on the wall. The recommended maximum torque is 26 inch-pounds Secure the cable guides with the two M6x12mm screws supplied with the cable kit. Position the cable A920-CBL-GUIDE (left and right) against the front of the chassis and align the two screw holes, as shown If the chassis is mounted using 19-inch brackets, you must assemble the cable guides before installing the chassis on the Use a tape measure and level to verify that the device is installed straight and on level. Position the device on the rack, and use the images as a guide to set up the device. Install cable guides before installing the device in a 19 inches (48.3 centimeters) EIA rack. Secure the bracket to the device with the recommended maximum torque of 10 inch-pounds (1.1 newton meters).Įnsure adequate clearance when mounting the device on a rack. Attaching Mounting Brackets to Router for a ETSI Rack (Rear Position) Attaching Mounting Brackets to Router for a ETSI Rack (Middle Position)įigure 12. Attaching Mounting Brackets to Router for a ETSI Rack (Front Position)įigure 11. Attaching Mounting Brackets to Router for a 23-inch EIA Rack (Rear Position)įigure 10. Attaching Mounting Brackets to Router for a 23-inch EIA Rack (Middle Position)įigure 9. Attaching Mounting Brackets to Router for a 23-inch EIA Rack (Front Position)įigure 8. Attaching Mounting Brackets to Router for a 19-inch EIA Rack (Rear Position)įigure 7. Attaching Mounting Brackets to Router for a 19-inch EIA Rack (Middle Position)įigure 6. Attaching Mounting Brackets to Router for a 19-inch EIA Rack (Front Position)įigure 5. You can install the brackets at any of the 3 positions that are shown in the figure.įigure 4. Remove the rack mounting brackets from the accessory kit and position them beside the device. The device is shipped with rack mounting brackets that are to be secured on the sides of the device. You can choose to either set up the router in a horizontal or a vertical mounting position on the rack. You can choose to either set up the Cisco ASR 920 Router on a rack or wall mount it. Rack specification EIA (19 inches and 23 inches) We recommend that you follow these rack specifications. Installing the Cisco ASR-920-20SZ-M Router involves these tasks:
Windows serial terminal with auto baud driver#
Uninstalling the Cisco USB Device Driver.Connecting to the Console Port Using Linux.
![windows serial terminal with auto baud windows serial terminal with auto baud](http://www.modemsite.com/56k/images/hyper-3.gif)
Windows serial terminal with auto baud mac os x#